TARK-Both Trailing Arm Drill/Tap Guide Kit for installing both key lock KeenSerts or Helicoil inserts

Description

A Drill /Tap guide for doing both HeliCoils AND Keenserts

HeliCoil replacement text under the Heading “additional Information”

Trailing Arm Repair Kit for use with Heli-Coils is Part# TARK-HC

The difference between kits -KS & -HC are the insert type you plan on using i.e KeenSerts or Heli-Coils. While the jig plate is the same for both kits, the drill & tap insert guides are different so make sure you use the correct inserts with the jig that you are ordering.

These kits DO NOT INCLUDE the drill, bottoming tap or inserts. You will also need a good quality tap lubricant for use in aluminum for both drilling and tapping. WD40 is an OK substitute.

Heli-Coils are also available from many sources but as a former NAPA store owner I’d just recommend you order NAPA part # BK 770-3082. This kit contains 12 inserts, the insertion tool and the tap. It DOES NOT INCLUDE a 21/64″ drill bit or tap lubricant. Additional inserts can be ordered under NAPA part #BK 770-3132.

Please specify the kit based on the threaded inserts that you will be using.

Trailing Arm Repair Kit for use with Heli-Coils is Part# TARK-HC

KeenSerts

Trailing Arm Repair Kit for use with KeenSerts is Part# TARK-KS

KeenSerts – also known as key-lock inserts these can be sourced at many places, I’ll use www.McMaster.com and their part numbers as these were used for our testing. However……McMaster only ships parts domestically, so anyone outside of the United States may want to order Heli-coils which are more readily available worldwide or substitute Recoil brand key lock inserts (very similar to KeenSerts) Recoil brand is available worldwide.

Please note that KeenSerts require an “X” drill size and 7/16-14 bottoming tap. There’s some confusion here because a 7/16-14 tap is labeled to use a “U” drill size, BUT the KeenSerts instructions specify the larger “X” drill size. So don’t make the mistake of using a “U” drill. The KeenSerts directions also call for a countersink but you won’t need one when you use this set-up. If you were “free-handing” the tap, the countersink helps to line you up and get you started. The tap guide used here does all of that for you.

McMaster Part#   Description   https://www.mcmaster.com/

92070A337 7 PIECE KIT with TOOL – BLACK-PHOSPHATE STEEL KEY-LOCK THREAD INSERT, 7-PC THIN WALL REPAIR KT,5/16″-24 INT,7/16″-14 EXT T

92070A250
PACKAGE OF 7 ADDITIONAL INSERTS – BLACK-PHOSPHATE STEEL KEY-LOCK THREAD INSERT, THIN WALL, 5/16″-24 INT THRD, 7/16″-14 EXT, 7/16″L,

1413K42
TAP MAGIC CUTTING AND TAPPING FLUID, FOR ALUMINUM, 4-OUNCE CONTAINER (can use WD40)

2521A644
GENERAL PURPOSE HIGH-SPEED STEEL HAND TAP, BOTTOMING, 7/16″-14, H3 PITCH DIAMETER, 4 FLUTE

2901A168
“X” SIZE DRILL BIT

Please specify the kit based on the threaded inserts that you will be using.

Helicoils

Heli-Coils are also available from many sources but as a former NAPA store owner I’d just recommend you order NAPA part # BK 770-3082. This kit contains 12 inserts, the insertion tool and the tap. It DOES NOT INCLUDE a 21/64″ drill bit or tap lubricant. Additional inserts can be ordered under NAPA part #BK 770-3132.

Please specify the kit based on the threaded inserts that you will be using.

key lock KeenSerts

One (1) Alignment Jig
One (1) Tap guide Helicoil
One (1) Drill guide Helicoil
One (1) Tap guide Keenserts
One (1) Drill guide Keenserts

Detailed documents, videos and downloads on installation can be found in Product Support under the Trailing Arm Kit section.

Also see:Trailing Arm Repair Kit – Set-Up | Trailing Arm Repair Kit (TAK) – Contents.

Download: the “Installation Tip” pdf for use with Inserts